Page 3 of 4
Re: PyPRP2 Questions from a Noob
Posted: Tue May 31, 2011 1:42 pm
by nathan2055
Uh oh. I added the marker and some cones for fun:
- This is my Blender window.
- cubeage2.png (142.42 KiB) Viewed 4541 times
But after exporting my changes didn't appear! I looked in my dat folder and found two sets of files, I deleted them both (one was probably a leftover from when I was using another file name). The problem continues:
- This is the Age in URU.
- cubeage1.png (79.05 KiB) Viewed 4541 times
Re: PyPRP2 Questions from a Noob
Posted: Tue May 31, 2011 1:49 pm
by Lontahv
If you think it's PyPRP2's fault, you can PM me or post a link to your blend file. I'll take a look at it, try to export it, and tell you what's going on.
Re: PyPRP2 Questions from a Noob
Posted: Tue May 31, 2011 1:54 pm
by Paradox
I've had an issue in the past where after exporting an Age a bunch of times and loading it in Uru after every export, Uru would just stop loading new versions. I don't know if it was a file caching issue or something else, but even deleting the files and replacing them with the new ones didn't have any effect.
Like all problems on Windows, rebooting makes it work again.
Re: PyPRP2 Questions from a Noob
Posted: Tue May 31, 2011 4:30 pm
by nathan2055
Paradox wrote:I've had an issue in the past where after exporting an Age a bunch of times and loading it in Uru after every export, Uru would just stop loading new versions. I don't know if it was a file caching issue or something else, but even deleting the files and replacing them with the new ones didn't have any effect.
Like all problems on Windows, rebooting makes it work again.
OK, I'll try that.
Lontahv wrote:If you think it's PyPRP2's fault, you can PM me or post a link to your blend file. I'll take a look at it, try to export it, and tell you what's going on.
If Paradox's suggestion doesn't work, I'll post the blend.
Re: PyPRP2 Questions from a Noob
Posted: Wed Jun 01, 2011 11:09 am
by nathan2055
It didn't work
. Here's the blend file:
- Cube Age.blend
- The blend file for my first Age, Cube Age.
- (725.47 KiB) Downloaded 337 times
Re: PyPRP2 Questions from a Noob
Posted: Wed Jun 01, 2011 11:46 am
by tachzusamm
Nathan, apply a material to the cones - it will work then
Re: PyPRP2 Questions from a Noob
Posted: Wed Jun 01, 2011 12:16 pm
by nathan2055
Edited the objects, I added material and colors. Exported and getting ready to link.
Re: PyPRP2 Questions from a Noob
Posted: Wed Jun 01, 2011 12:26 pm
by nathan2055
nathan2055 wrote:Edited the objects, I added material and colors. Exported and getting ready to link.
Linked in, and everything appeared fine! Here is a screenshot:
- New screenshot!
- cubeage1.png (101.31 KiB) Viewed 4491 times
I need to do something about that light though.
Re: PyPRP2 Questions from a Noob
Posted: Wed Jun 01, 2011 9:07 pm
by Chacal
Congrats! You have an Age.
The ground seems a little on the soft side, though.
I sink, therefore I am?
Re: PyPRP2 Questions from a Noob
Posted: Thu Jun 02, 2011 5:40 am
by Sirius
LOL ! I would rather grab the spawn point 2 units higher.
Meshes without material are skipped during the export ? Or are they exported but the mat skipped ?
I remember the old version stopped working if there wasn't any material on a visible mesh.